Plumber's Essentials: Your Key to Bathtub Installation
Plumber's Essentials: Your Key to Bathtub Installation
Blog Article
They are making a few good observations regarding Tools You Need to Install a New Bathtub overall in this post further down.
Installing a bath tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately challenging project. If the old bathtub is easily obtainable, the project can relocate quickly; if you need to open a wall to remove the old tub and place the brand-new bathtub, the job is a lot harder. In either instance, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old bathtub as well as embeded in the brand-new one. Make sure you have actually qualified yourself for the task and also fit trying it. As opposed to employing a contractor to take over a halfway-completed job, it is far better to consider employing one before you begin. Chances are you might need a professional plumber to make tube links.
This article will help you install a new bathtub in your restroom if you have actually currently purchased a brand-new tub and also don't need to alter the setup of your previous supply of water pipes.
Your tools and also material checklist should consist of the following:
Planning for the Installment
First of all, the sustaining structure supplied with the bath should be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets system to stop stress on the tub.
Fit the adaptable tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its final placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, turn on the taps to drain any type of water staying in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the limited accessibility that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a cloth all set for the staying water that will certainly originate from the pipelines. Once the supply pipelines have been gotten rid of, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming throughout this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing compound.
Prior to proceeding to fit the new taps, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the bath tub in the required position. The wood boards are valuable in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four tiny points.
The next goal is to make sure that the tub is leveled all round. This can be attained by examining the level as well as readjusting the feet on the tub till the spirit level checks out degree.
To mount faucets, fit the bottom of the furthest versatile faucet port to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Activate the water and also examine all joints as well as new pipework for leaks and also tighten them if necessary. Load the bathtub and likewise inspect the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the tub ought to wait up until the bathtub has actually been used at the very least when as this will certainly resolve it right into its last position.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin guaranteeing that the washing machines are in place between the faucet as well as the sink. Secure the tap in position with the producer offered backnut. Once the tap is firmly in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap ports. The previous type ought to be connected to the faucet ends first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture a rigid seal, causing the water to pass through the wall surface between the bathroom and also the tiling, bring about issues with wetness and feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes and cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of drenched newspaper or soft rope. Remember to always load the bathtub with water before securing, to enable the movement experienced when the tub remains in usage. The sealant can break relatively very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader about How to Install a Bathtub Yourself, I assumed sharing that topic was a good thing. Remember to take the opportunity to distribute this blog post if you appreciated it. We truly appreciate reading our article about Tools You Need to Install a New Bathtub .
Book Service Now Report this page